###enable hw decoding / license keys
decode_MPG2=0x6c652062
decode_WVC1=0x1c52305e
-###overclocking
-gpu_freq Sets core_freq, h264_freq, isp_freq, v3d_freq together. Default 250
-core_freq Frequency of GPU processor core in MHz. It has an impact on ARM performance since it drives L2 cache. Default 250
-h264_freq Frequency of hardware video block in MHz. Default 250
-isp_freq Frequency of image sensor pipeline block in MHz. Default 250
-v3d_freq Frequency of 3D block in MHz. Default 250
-avoid_pwm_pll Don't dedicate a pll to PWM audio. This will reduce analogue audio quality slightly. The spare PLL allows the core_freq to be set independently from the rest of the gpu allowing more control over overclocking. Default 0
-sdram_freq Frequency of SDRAM in MHz. Default 400
-over_voltage ARM/GPU core voltage adjust. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. [5] Default is 0 (1.2V). Values above 6 are only allowed when force_turbo or current_limit_override are specified (which set the warranty bit)
+###overclocking /boot/config.txt
+gpu_freq Sets core_freq, h264_freq, isp_freq, v3d_freq together. Default 250
+core_freq Frequency of GPU processor core in MHz. It has an impact on ARM performance since it drives L2 cache. Default 250
+h264_freq Frequency of hardware video block in MHz. Default 250
+isp_freq Frequency of image sensor pipeline block in MHz. Default 250
+v3d_freq Frequency of 3D block in MHz. Default 250
+avoid_pwm_pll Don't dedicate a pll to PWM audio. This will reduce analogue audio quality slightly. The spare PLL allows the core_freq to be set independently from the rest of the gpu allowing more control over overclocking. Default 0
+sdram_freq Frequency of SDRAM in MHz. Default 400
+over_voltage ARM/GPU core voltage adjust. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. [5] Default is 0 (1.2V). Values above 6 are only allowed when force_turbo or current_limit_override are specified (which set the warranty bit)
over_voltage_sdram Sets over_voltage_sdram_c, over_voltage_sdram_i, over_voltage_sdram_p together
over_voltage_sdram_c SDRAM controller voltage adjust. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V) [5]
over_voltage_sdram_i SDRAM I/O voltage adjust. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V)[5]
over_voltage_sdram_p SDRAM phy voltage adjust. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V)[5]
-force_turbo Disables dynamic cpufreq driver and minimum settings below. Enables h264/v3d/isp overclock options. Default 0. May set warranty bit.
-initial_turbo Enables turbo mode from boot for the given value in seconds (up to 60) or until cpufreq sets a frequency. Can help with sdcard corruption if overclocked. Default 0 [6]
-arm_freq_min Minimum value of arm_freq used for dynamic clocking. Default 700
-core_freq_min Minimum value of core_freq used for dynamic clocking. Default 250
-sdram_freq_min Minimum value of sdram_freq used for dynamic clocking. Default 400
+force_turbo Disables dynamic cpufreq driver and minimum settings below. Enables h264/v3d/isp overclock options. Default 0. May set warranty bit.
+initial_turbo Enables turbo mode from boot for the given value in seconds (up to 60) or until cpufreq sets a frequency. Can help with sdcard corruption if overclocked. Default 0 [6]
+arm_freq_min Minimum value of arm_freq used for dynamic clocking. Default 700
+core_freq_min Minimum value of core_freq used for dynamic clocking. Default 250
+sdram_freq_min Minimum value of sdram_freq used for dynamic clocking. Default 400
over_voltage_min Minimum value of over_voltage used for dynamic clocking. Default 0
-temp_limit Overheat protection. Sets clocks and voltages to default when the SoC reaches this Celsius value. Setting this higher than default voids warranty. Default 85
+temp_limit Overheat protection. Sets clocks and voltages to default when the SoC reaches this Celsius value. Setting this higher than default voids warranty. Default 85
current_limit_override Disables SMPS current limit protection when set to "0x5A000020". Can help if you are currently hitting a reboot failure when overclocking too high. May set warrany bit.[
+###Configures the base Raspberry Pi hardware /boot/config.txt
+audio Set to "on" to enable the onboard ALSA audio interface (default "off")
+i2c_arm Set to "on" to enable the ARM's i2c interface (default "off")
+i2c_vc Set to "on" to enable the i2c interface usually reserved for the VideoCore processor (default "off")
+i2c An alias for i2c_arm
+i2c_arm_baudrate Set the baudrate of the ARM's i2c interface (default "100000")
+i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface (default "100000")
+i2c_baudrate An alias for i2c_arm_baudrate
+i2s Set to "on" to enable the i2s interface (default "off")
+spi Set to "on" to enable the spi interfaces (default "off")
+random Set to "on" to enable the hardware random number generator (default "on")
+sd_overclock Clock (in MHz) to use when the MMC framework requests 50MHz
+sd_force_pio Disable DMA support for SD driver (default off)
+sd_pio_limit Number of blocks above which to use DMA for SD card (default 1)
+sd_debug Enable debug output from SD driver (default off)
+uart0 Set to "off" to disable uart0 (default "on")
+uart1 Set to "on" or "off" to enable or disable uart1 (default varies)
+watchdog Set to "on" to enable the hardware watchdog (default "off")
+act_led_trigger Choose which activity the LED tracks. Use "heartbeat" for a nice load indicator. (default "mmc")
+act_led_activelow Set to "on" to invert the sense of the LED (default "off") N.B. For Pi3 see pi3-act-led overlay.
+act_led_gpio Set which GPIO to use for the activity LED (in case you want to connect it to an external device)
+ (default "16" on a non-Plus board, "47" on a Plus or Pi 2)
+ N.B. For Pi3 see pi3-act-led overlay.
+pwr_led_trigger As for act_led_*, but using the PWR LED. Not available on Model A/B boards.
+pwr_led_activelow As for act_led_*, but using the PWR LED. Not available on Model A/B boards.
+pwr_led_gpio As for act_led_*, but using the PWR LED. Not available on Model A/B boards.
+###Touchcontroller ADS7846 Touch controller
+cs SPI bus Chip Select (default 1)
+speed SPI bus speed (default 2MHz, max 3.25MHz)
+penirq GPIO used for PENIRQ. REQUIRED
+penirq_pull Set GPIO pull (default 0=none, 2=pullup)
+swapxy Swap x and y axis
+xmin Minimum value on the X axis (default 0)
+ymin Minimum value on the Y axis (default 0)
+xmax Maximum value on the X axis (default 4095)
+ymax Maximum value on the Y axis (default 4095)
+pmin Minimum reported pressure value (default 0)
+pmax Maximum reported pressure value (default 65535)
+xohms Touchpanel sensitivity (X-plate resistance) (default 400)
###vcgencmd - alles anzeigen was möglich ist
vcgencmd commands
###cpu temperatur
projects / help / commitdiff